single and multiple SSID SSID on the Cisco Aironet

single and multiple SSID SSID on the Cisco Aironet - Hallo my friends,, This post is entitled single and multiple SSID SSID on the Cisco Aironet, All of the content is aim for reader satisfaction. Hopefully all the posts will be easy to understand and likeable.

single and multiple SSID SSID on the Cisco Aironet

on the occasion of my last blog we have learned about the changing operational Cisco Aironet into AAP in this link

Now we will create a single SSID beforehand will be on further to multiple SSID



========

single SSID

========

to create a single SSID, we will do the Console prior to entering commands into the Cisco Aironet, topology we make is

before config in the AP it's good to do testing first in its network with the way testing is done in leptop 01, whether in leptop these can be the internet is not, if at leptop 01 can already Internet with IP obtained from a DHCP server in the modem, the rest just do the config on the side of his AP

In Single SSID we only need one VLAN only and we can make by using Switch unmanagable and the following are its config

dot11 ssid Office-BPN
authentication open
guest-mode
mbssid guest-mode
exit
!
interface Dot11Radio0
ssid Office-BPN
no shutdown
exit
!
interface BVI1
ip address dhcp client-id GigabitEthernet0
exit
!
end

for verification

check whether the interface BVI1 already get an IP from the DHCP server? check whether it could default route from the DHCP server? check whether the radio interface ama interface gigabit already up up anything yet? check whether in leptop 02 get a wireless signal AP to see if there SSID "Office -BPN "in leptop 02?

to point 1 & 2 that we do in terms of its backend interface that is on the side toward gigabit modem for point 3 and 4 we check on the radio side of the AP toward leptop whether the radio path already exists nothing yet

visible image above:

of command "sh ip int bri" IP contained in the can from its DHCP IP radio 192.168.1.102interface (Dot11Radio0), interfaces and interface GigabitEthernet0 BVI1 status up there upsudah routing table ip default route with IP 192.168.1.254 is the ip default route obtained from a DHCP Server

Also seen in the picture above that the SSID "Office-BPN" already there and when we want to connect not be requested for a password to be had immediately status "Connected"

if we look at the ip address propertiesnya, you will see the following display

visible image above its SSID is "Office-BPN" with the IP address obtained from a DHCP in the "DHCP Enabled" contains Yes

seen in the image above ping status is successful, means successfully pulak Config single SSID without a password on the Cisco Aironet, then we will try to still single SSID but using password

Config to be a single SSID no password just add config

interface Dot11Radio0
encryption mode ciphers aes-ccm
exit
!
dot11 ssid Office-BPN
authentication key-management wpa version 2
wpa-psk ascii Indonesia
end

for verification sapa exactly as above difference later on when we will be required to login password authentication

enter the password, the password that you created in the "wpa-psk ascii Indonesia" brarti that we enter is "Indonesia". If you've finished please do testing like the above instructions and complete our own config SSID by using a password



==========

multiple SSID

==========

Gambar

Cisco Aironet seen in the picture will be 2 SSID, which certainly in the switch must support VLAN, our scenario is leptop-01 can access to server-01 and can go to the internet as well but leptop-02 because of VLAN-guest using the internet could only just

for this case we have only discussed in the Cisco Aironet AP course and to Switch only slightly, to config on the switch only slightly

vlan 10
VLAN name-Office
vlan 20
VLAN name-Guest
!
int Fa0 / 1
desc to Router
switchport mode trunk
exit
!
int Fa0 / 2
desc to Cisco Aironet
switchport mode trunk
exit
!
int Fa0 / 3
desc to Server
switchport mode access
switchport vlan 10
end

config in the AP for its better regenerated and enter the following config

dot11 ssid Guest-BPN
vlan 20
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
wpa-psk ascii 7 1331161C0C09162B2523
!
dot11 ssid Office-BPN
vlan 10
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 11201701181C0E1F0D2B
!
interface Dot11Radio0
encryption mode ciphers aes-ccm
vlan 10 mode encryption ciphers aes-ccm
vlan 20 mode encryption ciphers aes-ccm
ssid Guest-BPN
ssid Office-BPN
mbssid
!
interface Dot11Radio0.10
encapsulation dot1q 10
bridge-group 10
!
interface Dot11Radio0.20
encapsulation dot1q 20
bridge-group 20
!
interface GigabitEthernet0.10
encapsulation dot1q 10
bridge-group 10
!
interface GigabitEthernet0.20
encapsulation dot1q 20
bridge-group 20
end

after completing the configuration, verify as usual as above, and see the list of available wireless, whether the SSID that we created already exists?

it is clear that 2 SSID that we create already exists, then it's done on the Cisco Wireless Config's



Greetings from our Best-Path Network
IT Network Training & Consulting

Ok, That's all about single and multiple SSID SSID on the Cisco Aironet Thank you for visiting, and have a nice day

single and multiple SSID SSID on the Cisco Aironet